Axle

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 9.5” Differential (1990-on)
41201-69245
41201-69246
Made in Japan

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 8” High Pinion Differential
These are the alternative higher ratio for Land Cruiser 80 Series with high pinion 8” differentials.
41201-69226
41201-69225
Made in Japan

Axle Shaft, Left Front Inner (long) - Land Cruiser 70 Series w/8” High Pinion 01/1990-08/1999 (LJ71, LJ78, KZJ, HZJ71, 73, 75, 77)
43412-60100

Axle Shaft, Left Front Inner (long) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on
Toyota pn:
43412-60110
43412-60070 = old part number

Axle Shaft, Right Front Inner (short) - Land Cruiser 70 Series w/8” High Pinion 01/1990-08/1999 (LJ71, LJ78, KZJ, HZJ71, 73, 75, 77)
43411-60050
43411-60070

Axle Shaft, Right Front Inner (short) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on
43411-60040
43411-60090

Bearing, 8" HP Diff Carrier - Toyota Land Cruiser high pinion 8” E-Locker RH side
Toyota pn:
90366-75001

Note that the inner dimension of 45mm does not work with new generation ARB Air Lockers which now use an inner dimension of 50mm.

Knuckle /Trunion Bearing - Land Cruiser 70 & 80 series 09/1989 - up
Toyota pn:
90366-20003

These are the correct Koyo knuckle (aka trunion or king pin) bearings for your pre-1990 Toyota solid axle vehicle. Toyota part number:
90366-17001
90366-17007
90366-17001-77
Koyo - Japan

Bearing, Tapered Roller - for Mark's Gears split case counter shaft
Part Number: 32206JR
Koyo - Japan

Birfield CV Axle, Land Cruiser 70 & 105 Series 08/1999-on w/drive flange only (NTO)
43405-60100
Toyota - Japan

Birfield for the Land Cruiser 80 Series. Non-ABS.
Later version with the longer splined section to replace short splined versions that suffer spline/drive flange wear.
Toyota pn:
43405-60080 (246.5mm)
Engineered in Australia - Made in Taiwan

Replacement Birfield CV Axles for the Land Cruiser 80 Series with ABS.
Toyota pn:
43405-60070 = 246.5mm
43405-60060 (pn for shorter part that this replaces 238.5mm)
ABS ring is not supplied
Made in Taiwan

Birfield CV Axle, Nissan Safari/Patrol GQ Y60 Series 07/1989-12/1997

Birfield CV Axle, Toyota Land Cruiser 70 Series - 8" High Pinion  from the 1990 model year 08/1989 until approx 07/1999 (?)
Toyota pn: 43405-60040
Aftermarket

Cone Washer for Land Cruiser & Hilux steering knuckle. Toyota calls this part “dowell, split (for steering knuckle arm)”
42323-60020
Toyota - Japan

Diff Bearing Kit - Land Cruiser 9.5" non-locker w/crush sleeve
Koyo Bearings

Diff Bearing kit - 8" High Pinion non-locker Land Cruiser (1990 & on)
Koyo bearings in kit

Diff Bearing Kit - HP 8" w/Locker
Land Cruiser High Pinion 8" w/Factory Locker

Diff Bearing Kit - Land Cruiser 9.5" non-locker w/crush sleeve & 50mm bearings (1990-on)
Koyo Bearings

Diff Bearing kit 9.5" w/Locker
Land Cruiser with Factory Locker (e-locker, cable locker) 30mm pinion

Dowel Pin (7mm) - Toyota Front Hub, Rear Full Float Axle
Toyota pn:
90250-07057

Drive Flange - Land Cruiser 80 Series - Short splined drive flange for the early Birfield CV Axles.43421-60020

Joint Fuji - Made in Japan