Front Axle

Axle Shaft, Left Front Inner (long) - Land Cruiser 70 Series w/8” High Pinion 01/1990-08/1999 (LJ71, LJ78, KZJ, HZJ71, 73, 75, 77)
43412-60100

Axle Shaft, Left Front Inner (long) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on
Toyota pn:
43412-60110
43412-60070 = old part number

Axle Shaft, Right Front Inner (short) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on
43411-60040
43411-60090

Knuckle /Trunion Bearing - Land Cruiser 70 & 80 series 09/1989 - up
Toyota pn:
90366-20003

These are the correct Koyo knuckle (aka trunion or king pin) bearings for your pre-1990 Toyota solid axle vehicle. Toyota part number:
90366-17001
90366-17007
90366-17001-77
Koyo - Japan

Birfield CV Axle, Land Cruiser 70 & 105 Series 08/1999-on w/drive flange only (NTO)
43405-60100
Toyota - Japan

Birfield for the Land Cruiser 80 Series. Non-ABS.
Later version with the longer splined section to replace short splined versions that suffer spline/drive flange wear.
Toyota pn:
43405-60080 (246.5mm)
Engineered in Australia - Made in Taiwan

Replacement Birfield CV Axles for the Land Cruiser 80 Series with ABS.
Toyota pn:
43405-60070 = 246.5mm
43405-60060 (pn for shorter part that this replaces 238.5mm)
ABS ring is not supplied
Made in Taiwan

Birfield CV Axle, Nissan Safari/Patrol GQ Y60 Series 07/1989-12/1997

Birfield CV Axle, Toyota Land Cruiser 70 Series - 8" High Pinion  from the 1990 model year 08/1989 until approx 07/1999 (?)
Toyota pn: 43405-60040
Aftermarket

Drive Flange - Land Cruiser 80 Series - Short splined drive flange for the early Birfield CV Axles.43421-60020

Joint Fuji - Made in Japan

Drive Flange, Front Axle - Land Cruiser 80 Series with longer splines.
43421-60040
Toyota OEM or Joint Fuji - Japan

Dust Cap, Front Axle Outer Flange (hub cap)
43423-35010

Dust Seal, Front Axle Hub - Land Cruiser 80 & Late 70 Series
90313-93003
Toyota - Japan

Gasket, dust seal to backing plate - Land Cruiser 40, 50, 60, 70 & 80 series
43436-60011
Toyota - Japan

Gasket, Hub - Hub Body to Bearing Hub (multi hole)- Toyota Land Cruiser 80 Series (each)
Toyota pn:
43422-60060
43422-60030
Toyota - Japan

Gasket, Hub Cover Outer - Electric Locking Hub
43531-60030
43531-60031

Gasket, Hub/Drive Flange - locking hub to bearing hub - Land Cruiser 40, 50, 60, 70 series (multi hole)
43422-60010
Aftermarket - Taiwan

Gasket, Hub/Drive Flange - locking hub to bearing hub - Land Cruiser 40, 50, 60, 70 series (multi hole)
43422-60010
Toyota - Japan

Gasket, spindle to knuckle housing - Land Cruiser 80 & Late 70 Series (Octagonal)
Toyota pn:
43435-60020

Heavy Duty Knuckle Ball Wiper Seal & Backing Plates

For front and rear locking hubs, drive plates, and rear full floating axle shafts that use 8.0mm hub studs. Hub Stud Kit:
1x 8x1.25mm Stud
1x 8x1.25mm Nut
1x 8mm Lock Washer
1x Cone Washer

Toyota pn: 90116-08325
Made in Japan by Joint Fuji

This kit replaces the two 54mm nuts, the thrust washer, and the locking tab (aka: ‘star washer’) on Toyota Live Front Axles.
Kit Contents:
1x 90215-42025  “Star” lock Washer
1x 90214-42030  Thrust “Claw” Washer
2x 43521-60011  54mm Spindle Nuts

Knuckle Felt kit, 40, 60, 70 series - up to 1989 - 1 kit per side
Toyota pn:
43204-60020 AM
Made in Japan